Ford Explorer Rear End Identification
Identifying ford vehicles equipped with oe traction rear ends. Drop out style rear end;
Its hangin on the rear cover it will have a series of numbers and letters on it something like this.
Ford explorer rear end identification. The home page of ntrprize. And looking at the axle tag above, you can see it's a 3.73 gear ratio with a limited slip in a 8.8 inch axle. Welcome to the #1 explorer st forum and explorer st community dedicated to explorer st owners and enthusiasts.
Fortunately, you can tell a lot about a rear axle by its shape and number of bolts on the differential housing. If its a 9 its pass side front. Compare the gasket shape with the chart found on the drivetrain site (see references section).
Has removable pinion support on the front; The s in the code doesn't mean anything about the driveshaft because that dept. Ford usually has a metal tag hangin off one of the diff cover bolts.
However, road debris, dirt, grime, and general age can obscure these numbers. Rear axle codes can be found on the safety standard certification label attached to the left drivers side door lock post. Ford 7.5s and 8.8s have 10 bolts, the 10.25 has 12 and all dana units have 10 bolts, but each has a different gasket shape.
Please select a rear end that matches your vehicle below. The plate provides important information about the axle assembly, its date of manufacture and the location responsible for creating the part. This number contains vital information about the car, such as its manufacturer, year of production, the plant it was produced in, type of engine, model and more.
Of ford didn't deliver the rearend with the driveshaft attached. What is the width of a ford explorer rear end? Axle oil change | explorer st forum.
Register for an account, it's free and it's easy, so don't hesitate to join the explorer st forum today! For instance, if someone wants to buy a car, it is possible to check the vin number one the online. We make it easy to verify your exact rear end
Axle tag location and appearance may vary by application. It’s worth noting that rear axles can sometimes be positively identified by a casting number and date stamped on the differential cover or axle tube. How do i identify a ford 8.8 rear end?
Ford has a wide range of front and rear ends! You'll need to measure the axles you have and match them up at a junk yard. A ford tag number will appear something like 12d04 which signifies april 4, 2012, which makes ford rear end identification much simpler.
Everything else should bolt up fine. Ex 9 3 00 is an. Worst case scenario you'll need two rear ends to pull axles from.
Gm 8.2″ or 8.5″ gm. Click on the year or the information you need: Gm 8.2″ or 8.5″ gm.
To view all forums and unlock additional cool features. 9 3l75 that would be a 9 rear with 3.75 ratio and locking diff if theres no l between the numbers it has an open diff. According to the dana/spicer corporations' roadranger illustrated parts list, there are two identification tags, one located on the driver's side differential carrier and one on the passenger side of the axle housing.
If you are fortunate enough to find an axle with the identification tag still attached, it will help solve part. The cover is not quite square, measuring about 101/2 inches high by 11 inches long. The simplest way to identify the rear axle assembly of a ford vehicle is to look at the plate stamped on the component.
Explorer rears have an offset center section so axles etc. If its a newer 8.8 (like mustang, beware of the 7.5 ford go for the 8.8 or 9). 1991 1992 1993 1994 1995.
Won't be an exact swap over. In this regard, how do i identify a ford 8.8 rear end? Every ford car has a unique identifier code called a vin.
Identify by differential cover shape like we said, if it was as easy as reading a number, this article would’ve ended at the beginning.
Posting Komentar untuk "Ford Explorer Rear End Identification"